Announcement

Collapse
No announcement yet.

Router Woes

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Router Woes

    Well my first Router died (Linksys BEFSR41 V.2)..

    Luckily it was in the 30 day period so I exchanged it for another which happened to have a $15.00 rebate....LOL

    Port 4 which I was using on the first one quit working and I could not access the setup software or ping any of the other 3 ports

    So, back it went....

    I am curious about the setup on these routers. Do you guys set the router to "Obtain an IP Address Automatically" or do you set yours to "Specify an IP Address" ?????

    I set mine set to "Obtain an IP Address Automatically" this time and when I do the Port Scan At DSL Reports it sees open Ports. I set the first router to "Specify an IP Address" and it was very secure.

    I have my Linksys LNE100TX NIC set to specify an IP Address.

    Also have any of you who have this NIC enabled the "Turbo Mode" in the DOS diagnosis???? I wonder if it is faster in Turbo mode. The through-put increased from 44 Mbps to 70+Mbps in the diagnostic tests.

    Paul
    "Never interfere with the enemy when he is in the process of destroying himself"

  • #2
    If you set yours to Automatic, the router resolves all new Computers on the LAN with DHCP, otherwise you will be stuck with manually assigning IP addresses to your computers...(a major drag.)

    Stick with DHCP, it works well. I HATE adding in MACs or IPs manually...showmac and resolving bootp are so archaic...yet so common in mixed networks...

    As far as "Turbo" Mode, I think that is simply forcing the card to 100MBPS Full Duplex...which on a Router or a Switch, REALLY speeds things up. Full Duplex on a hub is something of a misnomer...

    A common practice where I work is to routinely dumb down PCs to 10 MBPS Half Duplex to keep the network running smoothly at smaller sites, or sites experiencing network overloads or random packet storms. Even Cisco Switches can get overwhelmed with a lot of "mixed" (IP and non-IP) traffic which exist at these sites.

    Though at the location where I work, we are running 100MBPS Full in a pure TCP/IP environment, but also run a LOT more servers, a LOT more Switches and a LOT more Fiber than most people have ever seen in one place, it is the exception, not the rule.
    Hey, Donny! We got us a German who wants to die for his country... Oblige him. - Lt. Aldo Raine

    Comment


    • #3
      Typically @Home has a static IP addy... so "Obtain an IP Address Automatically" shouldn't be needed unless you're on a dynamically assigned IP (aka DHCP or other).

      Not sure what you are refering to about the nic...

      What nic is it?
      "Be who you are and say what you feel, because those who mind don't matter, and those who matter don't mind." -- Dr. Seuss

      "Always do good. It will gratify some and astonish the rest." ~Mark Twain

      Comment


      • #4
        I would hardly call assigning IP's on a home network a major drag... it's simple and you always know what they are... helpful when something does go bump in the night.

        Hubs aren't full duplex, only half by function
        "Be who you are and say what you feel, because those who mind don't matter, and those who matter don't mind." -- Dr. Seuss

        "Always do good. It will gratify some and astonish the rest." ~Mark Twain

        Comment


        • #5
          That's why I mentioned Full Duplex on a hub being a Misnomer...it's not possible.

          He's got the Linksys LNE100TX...which actually is a pretty decent little NIC...

          The reason why you are showing Open ports is because the "master" port on the BEFSR41 is set to allow tunnelling - (you can shut it off at the Router, but then you won't be doing much gaming: without tunelling, you will not be able to join or host multiplayer games on the internet.) As to the open Port issue: Microsoft enables NetBIOS by default, but in Win98SE/Win2K, you CAN shut off NetBIOS...in WinME, you can't. You will get an Open Port 139 until you shut off NetBIOS, or until you mask the port with the Router.
          Last edited by MultimediaMan; 9 August 2001, 05:04.
          Hey, Donny! We got us a German who wants to die for his country... Oblige him. - Lt. Aldo Raine

          Comment


          • #6
            Couldn't see Pauls sig til now
            "Be who you are and say what you feel, because those who mind don't matter, and those who matter don't mind." -- Dr. Seuss

            "Always do good. It will gratify some and astonish the rest." ~Mark Twain

            Comment


            • #7
              No Worries...
              Hey, Donny! We got us a German who wants to die for his country... Oblige him. - Lt. Aldo Raine

              Comment


              • #8
                Thanks guys,

                I'm running plain old 98 so I'll look into shutting off NetBios when I get home.

                I almost thought that the new router was bad too. When I first installed it I couldn't ping or open the setup menu in NS or IE. I spent "too" much time trying to connect to it.

                I finally went back to basics...Reseated the NIC in the PCI slot and it finally worked....LOL

                Paul
                "Never interfere with the enemy when he is in the process of destroying himself"

                Comment


                • #9
                  Paul,
                  Be sure to update to the latest firmware (1.39) and
                  on the setup page:
                  Advanced -> Filters -> Block WAN Request -> ON.
                  Chuck
                  Chuck
                  秋音的爸爸

                  Comment


                  • #10
                    I'm Healthy now

                    Paul
                    "Never interfere with the enemy when he is in the process of destroying himself"

                    Comment


                    • #11
                      ALPM,
                      A port not working doesn't always mean it's broken. I have had ports on my linksys (also a 41) get jammed a couple of times. Resetting the link always helped (power off/on). It happens when garbage get send sent to the port. Like when i switch on my hub when its connected to a port on the linky ..this will jam the port every time..If i disconnect the hub from the linksys first it works fine.

                      Maybe your port really was bust...but just so that you throw it out the window right away if it happens again


                      So far I really liked the linksys, I have always been pro software solutions (always used ipchains before), but hese thingies make life much easier

                      Grtz,
                      Ed

                      Comment

                      Working...
                      X