Free beer on IRQ 11 :(

[Admiral]

0 System timer
1 Standard 101/102-Key or Microsoft Natural Keyboard
2 Programmable interrupt controller
3 Communications Port (COM2)
4 Communications Port (COM1)
5 (free)
6 Standard Floppy Disk Controller
7 Printer Port (LPT1)
8 System CMOS/real time clock
9 Rockwell HCF 56K Speakerphone PCI Modem
9 SCI IRQ used by ACPI bus
10 Vortex AU8830 Sound Blaster Pro Emulation
11 Vortex AU8830 PCI Audio
11 Rockwell PCI Modem Enumerator
11 Vortex AU8830 Multifunction PCI Platform
11 Intel(r) 82371AB/EB/MB PCI to USB Universal Host Controller
11 Matrox Millennium G400 DualHead - English
11 ACPI IRQ Holder for PCI IRQ Steering
11 ACPI IRQ Holder for PCI IRQ Steering
11 ACPI IRQ Holder for PCI IRQ Steering
11 ACPI IRQ Holder for PCI IRQ Steering
12 PS/2 Compatible Mouse Port
13 Numeric data processor
14 Primary IDE controller (dual fifo)
14 Intel(r) 82371AB/EB/MB PCI Bus Master IDE Controller
15 Secondary IDE controller (dual fifo)
15 Intel(r) 82371AB/EB/MB PCI Bus Master IDE Controller

Using a MSI 6163 Pro mobo.
How do I move some of those devices ?

[DuRaNgO]

#1: go to pnp/pci config in your bios
#2: set resources controlled by to manual
#3: set irq 5 to isa
#4: set reset config. data to enable
#5: reboot
see if that helps first
jim

[EDIT]be sure not to have a card in the first slot nearest the vid card (if the first doesn't work)[/EDIT]

------------------
P3-700e @ 1052! Check it here!
Abit BE6-2
TwinMos 128mb pc-133
G400 (vanilla!!!) 32mb @ 167/208
Maxtor 15.3gb 7,200rpm
SB Live!
Winblows 98se & DX7
and 384k DSL!

[This message has been edited by DuRaNgO (edited 02 August 2000).]

[Admiral]

0 System timer
1 Standard 101/102-Key or Microsoft Natural Keyboard
2 Programmable interrupt controller
3 Communications Port (COM2)
4 Communications Port (COM1)
5 Vortex AU8830 Sound Blaster Pro Emulation
6 Standard Floppy Disk Controller
7 Printer Port (LPT1)
8 System CMOS/real time clock
9 Vortex AU8830 PCI Audio
9 Rockwell HCF 56K Speakerphone PCI Modem
9 Rockwell PCI Modem Enumerator
9 Vortex AU8830 Multifunction PCI Platform
9 ACPI IRQ Holder for PCI IRQ Steering
9 ACPI IRQ Holder for PCI IRQ Steering
9 SCI IRQ used by ACPI bus
10 Intel(r) 82371AB/EB/MB PCI to USB Universal Host Controller
10 ACPI IRQ Holder for PCI IRQ Steering
11 Matrox Millennium G400 DualHead - English
11 ACPI IRQ Holder for PCI IRQ Steering
12 PS/2 Compatible Mouse Port
13 Numeric data processor
14 Primary IDE controller (dual fifo)
14 Intel(r) 82371AB/EB/MB PCI Bus Master IDE Controller
15 Secondary IDE controller (dual fifo)
15 Intel(r) 82371AB/EB/MB PCI Bus Master IDE Controller

Thanks

One more thing. I have a 650 Cumine and my Quake 3 fps (timedemo1, 800x600x32, bilinear, everything else on high) don't go over 43. I was geting 39 with a 450 Katmai and was hoping for more from a 200 Mhz boost.
I tryed with PD 5.52 and the two betas, both ICD and TurboGL (6 combos, 2 per driver version). Is this normal ?

My 3DMark2000 scores are between 2800-2870 (default benchmark), depending on the driver version I use (beta scores higher).

[DuRaNgO]

Have you tried it with the new irq settings?

Also, use the new 6.01beta drivers

They work very well and you don't need the tgl (be sure to remove it from you Q3 folder and any other games as well

[Admiral]

I tryed it with the new IRQ settings. All the combinations, again. Tryed optimizing the OpenGl for speed with the TS utility (with beta 6.0 and 6.01), same scores.
Overclocked the CPU to 866, nothing above 43.
My 3DMark 2000 scores rised to 3055 when I overclocked the CPU.

[Rakido]

Admiral,

there was already a thread about this here : http://forums.murc.ws/ubb/Forum4/HTML/004021.html

Haven't checked, if there's a solution inside.

Rakido

[Admiral]

Thanks Rakido, it seems that's what the card is capable of, something around 47 fps.
Had to overclock my vanilla to 150/200 to get 47.
Geting 3563 in 3DMark at 866 with PD 6.01.
Beside higher 3DMark scores and D3D games runing smoother, I didn't saw much of an improvement.