Tweet
Hi All,
Hope to get some feedback reagrding this.
The real problem is here :
Have tried to install NT Workstation and NT Server. Installing the OSes was successfully. When installing the drivers for the G400 MAX, I inserted the CDROM Drivers and went through the necessary steps. System rebooted and was fine. Went to the Powerdesk and set my Monitor to DDC. Nothing wrong. Set resolution to 32bit 1024X768 Large fonts, nothing wrong. But I noticed that the Dual Head icon was not accessable. Proceed to check the box under "Use secondary display.......". Dual Head icon can be accessed. When I clicked it and prompted to accept, it just went back itself to the single display icon. When I checked the View Max box, the system went into Blue Screen.
I removed the drivers and attempted to reinstall. No problems. But when I check the "Use secondary display as.....", Blue Screen again. At times this box can be checked and sometimes impossible resulting in the crash.
Anyone successfully managed to get it set up in NT ? Please advise me.
Thanks a lot for reading.
Regards.
Rodent
BTW my system configuration's as follows :
Dual P3-450MHz
MS6120 w/SCSI Bios V1.8
192MB PC100 SDRAM
CL SB PCI128
Matrox G400 MAX 32MB AGP
Promise ATA66 Card
IBM 9.1GB 7200rpm ATA66 HDD (on Promise)
Quantum EX3.2 ATA33 HDD (onboard Secondary IDE Master)
IBM 1.7GB HDD (onboard Secondary IDE Slave)
Pioneer 6X DVD Rom (onboard Primary IDE Master)
Creative 40X infra CDrom (onboard Primary IDE Slave)
------------------
PIII 500MHz
Gigabyte BX2000
128MB SDRAM
Pioneer 24X IDE CD-ROM
Pioneer 6X/32X IDE DVD Drive
Yamaha 4260 SCSI CD-Rewritable Drive
2 X IBM 9.1 HDD
G400 32MB Dual Head
AWE64 Gold
ACS45.1 Speakers
17" Viewsonic
17" LG Flatron
Hope to get some feedback reagrding this.
The real problem is here :
Have tried to install NT Workstation and NT Server. Installing the OSes was successfully. When installing the drivers for the G400 MAX, I inserted the CDROM Drivers and went through the necessary steps. System rebooted and was fine. Went to the Powerdesk and set my Monitor to DDC. Nothing wrong. Set resolution to 32bit 1024X768 Large fonts, nothing wrong. But I noticed that the Dual Head icon was not accessable. Proceed to check the box under "Use secondary display.......". Dual Head icon can be accessed. When I clicked it and prompted to accept, it just went back itself to the single display icon. When I checked the View Max box, the system went into Blue Screen.
I removed the drivers and attempted to reinstall. No problems. But when I check the "Use secondary display as.....", Blue Screen again. At times this box can be checked and sometimes impossible resulting in the crash.
Anyone successfully managed to get it set up in NT ? Please advise me.
Thanks a lot for reading.
Regards.
Rodent
BTW my system configuration's as follows :
Dual P3-450MHz
MS6120 w/SCSI Bios V1.8
192MB PC100 SDRAM
CL SB PCI128
Matrox G400 MAX 32MB AGP
Promise ATA66 Card
IBM 9.1GB 7200rpm ATA66 HDD (on Promise)
Quantum EX3.2 ATA33 HDD (onboard Secondary IDE Master)
IBM 1.7GB HDD (onboard Secondary IDE Slave)
Pioneer 6X DVD Rom (onboard Primary IDE Master)
Creative 40X infra CDrom (onboard Primary IDE Slave)
------------------
PIII 500MHz
Gigabyte BX2000
128MB SDRAM
Pioneer 24X IDE CD-ROM
Pioneer 6X/32X IDE DVD Drive
Yamaha 4260 SCSI CD-Rewritable Drive
2 X IBM 9.1 HDD
G400 32MB Dual Head
AWE64 Gold
ACS45.1 Speakers
17" Viewsonic
17" LG Flatron