Tweet
this looks really cool and it's not too many years away from beeing commercialy available
Published online: 29 April 2007; | doi:10.1038/news070423-11
Plastic sheet delivers wireless power
Desks and walls could one day light up electronics without need for cables.
Tom Geller
Annoyed by the tangle of power cords under your desk? A sheet of plastic invented by researchers in Japan could one day make for tables and walls that power devices placed on them — without any need for wires or plugs. Computers could be powered through the desks on which they sit, for example, or flat-screen televisions through the walls where they hang.
This table can power a light placed above it — even one that's underwater.
The team of seven researchers at the University of Tokyo has produced a sample sheet of the plastic, which is about the size of a very thin magazine — just one millimetre thick and weighing 50 grams. It can deliver up to 40 watts of power to products on or near it that contain a special 'receiving coil': enough to power a lightbulb or a very small laptop. They say that scaled-up production of such sheets could be inexpensive enough for widespread installation in desks, floors, ceilings and walls, ushering in a "new class of electronic devices".
The plastic, described today in Nature Materials1, has as its base a layer of transistor featuring pentacene, an organic molecule whose electrical conductivity can be controlled. Topping that are layers holding copper coils that can sense whether a compatible electronic device is nearby, microelectromechanical-system (MEMS) switches that serve to turn on and off the power, and copper coils to transmit electricity.
When the sheet itself is plugged in, it can power devices — such as light-emitting diodes (LEDs) strung on a Christmas tree — that are built with a matching receiver coil. When these are placed within 2.5 centimetres of the sheet, the nearest MEMS switch turns on, feeding power to the closest sender coil, which powers the device's receiving coil through induction.
The researchers say the transmission of power happens with 81.4% efficiency — compared to 93% efficiency in the wired grid network as a whole — with a "quite low" level of leaked electromagnetic radiation. As a demonstration of the product's safety, the paper shows it powering an LED at the bottom of a bowl containing water and a live fish.
All four layers are produced by literally printing them — the coils using screen printing, the switch and transistor layers with an ink-jet printer (using special electronic inks). So the product is thin, lightweight and mechanically flexible.
Power pad
Wireless power systems are nothing new: many electric toothbrushes are charged wirelessly by standing them in a powered base where electrical contacts come in touch with each other, for example. And several companies offer power 'pads' that, when plugged in, will charge specially developed devices, such as compatible mobile phones, simply by placing them anywhere on the pad's surface. But these use silicon-based transistors, which are harder to manufacture and so are more expensive. Printable organic transistors can theoretically be made of any size, at a considerably lower cost.
Roger T. Howe, an electrical engineer at Stanford University in Palo Alto, California, is impressed by the work. "The demonstration of both organic transistors and MEMS switches in a useful system makes it impressive," he says.
But don't throw out your power cords yet: the researchers say that these plastic power sheets probably won't hit the market for 5 years, while they improve their reliability and stability. However, they have received "lots of feedback from many companies", and project a target manufacturing cost of US$100 per square metre. Then there's still the trick of getting device manufacturers to put the receiving coils into their products to make them compatible. But should that happen, you may someday enjoy a world with ubiquitous power — and no power cords.
Plastic sheet delivers wireless power
Desks and walls could one day light up electronics without need for cables.
Tom Geller
Annoyed by the tangle of power cords under your desk? A sheet of plastic invented by researchers in Japan could one day make for tables and walls that power devices placed on them — without any need for wires or plugs. Computers could be powered through the desks on which they sit, for example, or flat-screen televisions through the walls where they hang.
This table can power a light placed above it — even one that's underwater.
The team of seven researchers at the University of Tokyo has produced a sample sheet of the plastic, which is about the size of a very thin magazine — just one millimetre thick and weighing 50 grams. It can deliver up to 40 watts of power to products on or near it that contain a special 'receiving coil': enough to power a lightbulb or a very small laptop. They say that scaled-up production of such sheets could be inexpensive enough for widespread installation in desks, floors, ceilings and walls, ushering in a "new class of electronic devices".
The plastic, described today in Nature Materials1, has as its base a layer of transistor featuring pentacene, an organic molecule whose electrical conductivity can be controlled. Topping that are layers holding copper coils that can sense whether a compatible electronic device is nearby, microelectromechanical-system (MEMS) switches that serve to turn on and off the power, and copper coils to transmit electricity.
When the sheet itself is plugged in, it can power devices — such as light-emitting diodes (LEDs) strung on a Christmas tree — that are built with a matching receiver coil. When these are placed within 2.5 centimetres of the sheet, the nearest MEMS switch turns on, feeding power to the closest sender coil, which powers the device's receiving coil through induction.
The researchers say the transmission of power happens with 81.4% efficiency — compared to 93% efficiency in the wired grid network as a whole — with a "quite low" level of leaked electromagnetic radiation. As a demonstration of the product's safety, the paper shows it powering an LED at the bottom of a bowl containing water and a live fish.
All four layers are produced by literally printing them — the coils using screen printing, the switch and transistor layers with an ink-jet printer (using special electronic inks). So the product is thin, lightweight and mechanically flexible.
Power pad
Wireless power systems are nothing new: many electric toothbrushes are charged wirelessly by standing them in a powered base where electrical contacts come in touch with each other, for example. And several companies offer power 'pads' that, when plugged in, will charge specially developed devices, such as compatible mobile phones, simply by placing them anywhere on the pad's surface. But these use silicon-based transistors, which are harder to manufacture and so are more expensive. Printable organic transistors can theoretically be made of any size, at a considerably lower cost.
Roger T. Howe, an electrical engineer at Stanford University in Palo Alto, California, is impressed by the work. "The demonstration of both organic transistors and MEMS switches in a useful system makes it impressive," he says.
But don't throw out your power cords yet: the researchers say that these plastic power sheets probably won't hit the market for 5 years, while they improve their reliability and stability. However, they have received "lots of feedback from many companies", and project a target manufacturing cost of US$100 per square metre. Then there's still the trick of getting device manufacturers to put the receiving coils into their products to make them compatible. But should that happen, you may someday enjoy a world with ubiquitous power — and no power cords.
Comment